Skip to content

TPO Roofing Cost: What Public Bids, Spec Sheets and Codes Show

Flat white membrane roof on a low commercial building with rooftop units and rolls of roofing membrane

TPO roofing cost on five April 2026 public re-roof bids in Columbus, Georgia ran $11.76 to $18.93 per sq ft for 12,500 to 17,500 sq ft; roofs under 3,500 sq ft bid $28.64 to $44.05 in 2022.

Key takeaways

  • Five bids for the TPO fleeceback re-roof of the Pop Austin Recreation Center came in at $11.76 to $18.93 per sq ft, median $15.50, on 12,500 to 17,500 sq ft (Columbus Consolidated Government, RFB 26-0033, April 30, 2026).
  • Small roofs cost more per sq ft: two bids on about 3,100 sq ft at Edgewood Senior Center equal $28.64 and $44.05 per sq ft (Columbus RFB 23-0007, September 2022), and a 6,396 sq ft TPO replacement for the Federal Aviation Administration in Memphis was awarded at $37.33 per sq ft (USAspending.gov, award 697DCK24C00172, March 2024).
  • Insulation outweighs the membrane on a tear-off: at the median unit prices in Tulsa’s 2023 roofing contract, three 1.5-inch polyiso layers plus a 1/2-inch cover board sum to $6.83 per sq ft, 61.8% of an $11.05 layer sum, while 60-mil fully adhered TPO was $3.25 (City of Tulsa, TAC 1015B and 1015C, 2023).
  • Washington State University accepted a mechanically fastened 115-mil TPO fleeceback overlay of 32,200 sq ft for $284,000, or $8.82 per sq ft, 33.8% of the lowest full replacement bid (WSU bid results, March 2023).
  • ASTM D6878-13 requires at least 30% of nominal thickness over the scrim: 18 mils on a 60-mil sheet and 24 mils on an 80-mil sheet (NRCA Professional Roofing, August 2017).
  • The BLS Producer Price Index for nonresidential roofing contractors averaged 59.8% higher in 2025 than in 2019, and the preliminary September 2026 reading is 5.7% above September 2025 (BLS series PCU23816X23816X).

How much does a TPO roof cost per square foot?

Public bids with a stated roof area put a commercial TPO re-roof at $11.76 to $18.93 per sq ft for 12,500 to 17,500 sq ft in April 2026, which is $1,176 to $1,893 per 100 sq ft roofing square. Smaller and federal jobs bid higher: $28.64 to $44.05 per sq ft under 3,500 sq ft in 2022, and $37.33 on a 6,396 sq ft Federal Aviation Administration job in 2024.

Each row below divides a base bid by the roof area printed on the same public record. A base bid includes flashings, edge metal, drains, mobilization and bonds that a membrane-only unit price leaves out, so it sits well above the $3 to $8 ranges that consumer cost guides quote. The last price column moves each figure to September 2026 with the BLS Producer Price Index for nonresidential roofing contractors (series PCU23816X23816X).

Project, placeBid or award dateRoof area (sq ft)TPO scope on the recordBase bid or award$ per sq ftSep 2026 $ per sq ft (PPI)Source
Pop Austin Recreation Center, Columbus, GAApr 30, 202612,500 to 17,500 (5 bids)TPO fleeceback; Carlisle named in 3 of 5 bids$160,918 to $247,736$11.76 to $18.93 (median $15.50)$12.04 to $19.38Columbus RFB 26-0033
Metra Lower Maintenance Shop, Columbus, GAJul 6, 20229,100 to 10,400 (4 bids)TPO; Carlisle or Johns Manville; base also extends metal wall panels$284,700 to $388,523$31.29 to $37.96 (median $35.26)$39.57 to $48.01Columbus RFB 22-0041
Edgewood Senior Center, Columbus, GASep 28, 20223,025 and 3,200 (2 bids)TPO roof system$91,644.50 to $133,255$28.64 to $44.05 (median $36.35)$36.10 to $55.53Columbus RFB 23-0007
Federal Aviation Administration, Memphis, TNMar 26, 20246,396Remove existing TPO system, replace roof; 14 offers$238,735 award$37.33$41.86USAspending 697DCK24C00172
Food Service Building, Washington State University, Pullman, WAMar 20, 202332,200Recover: 115-mil TPO fleeceback, mechanically fastened over modified bitumen$284,000 award$8.82$10.29WSU bid results
TPO roofing bids per sq ft, by projectBar chart: TPO bids per sq ft were $8.82 for the WSU recover, $15.50 at Pop Austin, $35.26 at Metra, $36.35 at Edgewood and $37.33 for FAA Memphis.$ per sq ftWSU recover, 32,200 sq ft, 20238.82Pop Austin, 12,500 to 17,500 sq ft, 202615.5Metra shop, 9,100 to 10,400 sq ft, 202235.3Edgewood, about 3,100 sq ft, 202236.4FAA Memphis, 6,396 sq ft, 202437.3
Median TPO bid per sq ft ranged from $8.82 for a 32,200 sq ft recover to $37.33 for a 6,396 sq ft federal replacement. Sources: Columbus, GA bid tabulations 2022 to 2026, WSU 2023, USAspending.gov 2024; accessed November 1, 2026.

The Columbus tabulation prints the measured area next to each base bid, which is what makes a per-sq-ft figure possible. Bidders measured the same Pop Austin roof at 12,500 to 17,500 sq ft, a 40% spread, so check the area before comparing two quotes. Our guide on leveling bids explains how to compare construction bids.

Columbus RFB 26-0033 bid tab with the Pop Austin square footage and base bid rows boxed
Columbus Consolidated Government, RFB 26-0033 revised bid tabulation (April 30, 2026), page 1, boxed: measured roof areas of 12,500 to 17,500 sq ft and base bids of $160,918 to $247,736. Accessed November 1, 2026.

For a whole-building budget rather than a roof line, use our figures on commercial construction cost per square foot.

What do federal TPO awards specify?

Federal TPO awards on USAspending.gov state the membrane, attachment and insulation target more often than the roof area. Three awards from 2025 and 2026 show the spread: 60-mil mechanically fastened over a high-density cover board to R-30 for U.S. Customs and Border Protection, 72-mil fully adhered with R-38 at Fort Bliss, and 135-mil fleeceback at Fort Sill.

Agency, placePerformance startAwardMembrane and attachmentInsulation and boardSource
U.S. Customs and Border Protection, McAllen, TXOct 1, 2026$1,362,155.8260-mil TPO, mechanically fastenedHigh-density cover board; minimum R-30 assemblyUSAspending 70B01C26C00000113
U.S. Army, Fort Bliss, TX (Bldg 2416)Sep 15, 2025$466,40072-mil TPO, fully adheredR-38 insulation; 5/8-inch glass-mat roof boardUSAspending W911SG25CA044
U.S. Army, Fort Sill, OK (Bldg 2025)Aug 26, 2025$2,197,859135-mil fleeceback TPO, with clay barrel tile repairNot stated in the award textUSAspending W912BV25FA033

None of these three award records states a roof area, so they serve as specification benchmarks, not prices per sq ft. A private owner sets the same three items in the bid documents: membrane thickness, attachment method and the R-value or U-factor the energy code requires.

How much of a TPO roof’s cost is insulation and cover board?

On a tear-off, insulation and cover board usually cost more than the TPO sheet. In the City of Tulsa’s 2023 roofing contract, three 1.5-inch polyiso layers at a median $1.86 each plus a $1.25 fiberboard cover board came to $6.83 per sq ft, 61.8% of an $11.05 layer total; the 60-mil fully adhered membrane was $3.25, or 29.4%.

Line item (Tulsa specification)Bid A, May 25, 2023Bid B, Jun 15, 2023Bid C, Jun 15, 2023MedianSource
Remove built-up or single-ply roofing to the deck, per sq ft$0.97$0.97$1.25$0.97TAC 1015B, 1015C
Polyiso 1.5 in, LTTR R-9.0, mechanically fastened, per sq ft$1.86$1.90$1.75$1.86Tulsa
High-density fiberboard 1/2 in, mechanically fastened, per sq ft$1.25$1.27$1.10$1.25Tulsa
High-density fiberboard 1/2 in, set in hot asphalt, per sq ft$1.39$1.41$1.25$1.39Tulsa
TPO 60 mil, reinforced, fully adhered, per sq ft$3.25$3.27$3.00$3.25Tulsa
EPDM 60 mil, fully adhered, per sq ft$4.17$4.19$3.75$4.17Tulsa
TPO 60 mil flashing membrane, per sq ft$7.26$7.28$4.20$7.26Tulsa
Tear-off TPO roof layers and their unit prices Cross-section of a tear-off TPO roof with Tulsa 2023 contract unit prices for each layer and the share insulation and cover board take. What each layer of a tear-off TPO roof cost in Tulsa's 2023 roofing contract Median of 3 bids per line, dollars per sq ft, labor and material; flashing, edge metal and mobilization excluded 60-mil TPO membrane, fully adhered $3.25 range $3.00 to $3.27 1/2 in high-density fiberboard cover board, fastened $1.25 range $1.10 to $1.27 Polyiso 1.5 in, LTTR R-9.0, layer 3 $1.86 range $1.75 to $1.90 Polyiso 1.5 in, LTTR R-9.0, layer 2 $1.86 range $1.75 to $1.90 Polyiso 1.5 in, LTTR R-9.0, layer 1 $1.86 range $1.75 to $1.90 Tear-off of existing roof to the deck $0.97 range $0.97 to $1.25 Existing structural deck Sum: $11.05 per sq ft (2023); insulation and cover board $6.83 of it (61.8%), membrane $3.25 (29.4%) Escalated with BLS PPI for nonresidential roofing contractors (Jun 2023 to Sep 2026, x1.1274): $12.46
Layer by layer, a tear-off TPO roof summed to $11.05 per sq ft at Tulsa’s 2023 contract medians, 61.8% of it insulation and cover board. Source: City of Tulsa TAC 1015B and 1015C (2023), BLS PPI; accessed November 1, 2026.

Three 1.5-inch boards rated LTTR R-9.0 each give R-27 by simple sum, and each added layer costs $1.75 to $1.90 per sq ft at Tulsa’s 2023 prices. Penn State’s February 2025 bid priced replacing damaged 2.6-inch polyiso at $2.50 to $10.00 per sq ft across four bidders, which shows how much higher small-quantity repair prices run than contract-scale ones.

The insulation target on a tear-off comes from the energy code your jurisdiction enforces. Our commercial energy code by state table shows which IECC or ASHRAE 90.1 edition applies where.

Does 45, 60 or 80 mil change the price?

Thickness changes only the membrane line, about 29% of a tear-off in Tulsa’s 2023 unit prices, so moving from 60 to 80 mil shifts the finished price far less than the sheet price. None of the 11 public bid and award records we compiled priced 60 and 80 mil side by side; the maker sheets show what each thickness buys instead.

Product lineNominal thicknessThickness over scrimDynamic puncture, ASTM D5635Warranty or guarantee terms on the sheetSource, date
Carlisle Sure-Weld45 mil0.018 in typicalWatertight at 12.5 JNot on the data sheetCarlisle TDS 08.11.14 (2014)
Carlisle Sure-Weld60 mil0.024 in typicalWatertight at 22.5 JNot on the data sheetCarlisle, 2014
Carlisle Sure-Weld EXTRA80 mil0.034 in typicalWatertight at 30.0 JNot on the data sheetCarlisle, 2014
Duro-Last Duro-TECH TPO6060 mil30 mil (0.76 mm)50 J15, 20 or 25 yearsDuro-Last PDS, Oct 14, 2024
Duro-Last Duro-TECH TPO8080 mil37 mil (0.94 mm)60 J15, 20 or 25 yearsDuro-Last PDS, 2024
Johns Manville JM TPO80 mil0.033 inPass at 25 JPeak Advantage, 5 to 30 yearsJM RS-8634 (2016)
ASTM D6878-13 minimum60 and 80 mil18 and 24 mils (30% of nominal)No requirementNot applicableNRCA, Aug 2017

Puncture values come from each maker’s own test setup, so compare them within one maker’s sheet, not across brands. On Carlisle’s sheet, the 80-mil EXTRA stayed watertight at 30.0 J of impact against 22.5 J for 60 mil and 12.5 J for 45 mil.

What does ASTM D6878 require for thickness?

ASTM D6878 is the material standard for TPO sheet roofing. Since the 2013 edition it requires the coating over the reinforcing scrim on the weathering side to be at least 30% of nominal thickness: 18 mils on a 60-mil sheet and 24 mils on an 80-mil sheet, according to NRCA. Its physical property limits were set using 45-mil sheets.

Total sheet thickness has a tolerance too: JM’s 2016 sheet lists plus or minus 10% from nominal, and Carlisle’s 2014 sheet lists the D6878 limit as plus 15 or minus 10%. At the low limit, a 60-mil sheet can measure 54 mils (60 x 0.90). Ask each bidder to name the product line, submit the current data sheet and allow a membrane core cut at closeout if the specification calls for a thickness check.

Is 80 mil worth paying for?

On the maker sheets, 80 mil buys weathering layer and puncture resistance, not a longer warranty: Duro-Last lists the same 15, 20 and 25-year options for its 60 and 80-mil Duro-TECH sheets (October 2024). Duro-TECH TPO80 carries 37 mils over the scrim against 30 mils for TPO60, and its dynamic puncture rating rises from 50 J to 60 J.

The case for 80 mil therefore rests on traffic and impact. Roofs with rooftop units that technicians walk to, or roofs in hail country, are where those 7 extra mils over the scrim and the 10 J of extra puncture rating come into play.

Does the attachment method change TPO roofing cost?

Attachment sets how much fastening or adhesive goes under the sheet, but public bids rarely price it as its own line. In the records we compiled, fully adhered 60-mil TPO priced at $3.00 to $3.27 per sq ft in Tulsa’s 2023 contract, a mechanically fastened fleeceback recover cost $8.82 per sq ft in total at Washington State University, and federal awards specify both methods.

MethodHow the sheet is heldPublic record that specified itPrice on the recordSource
Mechanically fastenedScrews and plates in the seam laps; the next sheet is welded over themWSU 2023 recover (115-mil fleeceback, 32,200 sq ft); CBP McAllen 2026 (60-mil over high-density cover board)$8.82 per sq ft complete recover (WSU); CBP $1,362,155.82, area not statedWSU; USAspending
Fully adheredBonded to the cover board with adhesive across the whole sheetTulsa 2023 contract; Fort Bliss 2025 (72-mil, R-38)$3.00 to $3.27 per sq ft for the membrane line (Tulsa); Fort Bliss $466,400, area not statedTulsa; USAspending
Induction weldedPlates fastened through the insulation, then heat-bonded to the underside of the sheet with an induction tool; no fasteners in the lapsNone of the 11 recordsNo public price foundCB&C review of 11 records, Nov 2026

What moves the fastening price is the wind design at the roof edges. Tulsa’s polyiso line, for example, requires one fastener per 1.33 sq ft in the perimeter 8 feet and one per sq ft in the 8 ft by 8 ft corners, so a roof with more edge per sq ft uses more fasteners. Large distribution roofs, with little edge per sq ft, are covered in our warehouse construction guide.

Tear-off or recover: which applies and what does each cost?

A recover lays new TPO over the existing roof and skips removal and most insulation; a tear-off strips the roof to the deck. Washington State University’s 2023 bid shows the gap: a mechanically fastened 115-mil fleeceback overlay of 32,200 sq ft was accepted at $284,000, against $840,000 to $1,045,200 to remove and replace. The building code decides whether a recover is allowed.

Tear-off or recover decision for a TPO roof Four code questions from IBC 1512.3 and IECC C503.2.1 that decide whether a TPO roof can be recovered and what insulation a tear-off must add. Tear-off or recover a TPO roof: the code questions in order 1. Two or more roof coverings already on the deck? If no, go down Yes: tear off to deck IBC 1512.3 2. Existing roof water-soaked or deteriorated? If no, go down Yes: tear off to deck IBC 1512.3 3. Existing covering slate, clay, cement or asbestos-cement tile? If no, go down Yes: tear off to deck IBC 1512.3 Recover permitted: overlay TPO on the existing roof WSU 2023: $8.82 per sq ft recover vs $26.09 low replacement bid After a tear-off: 4. Insulation entirely above the deck removed? IECC C503.2.1 (2021), per Philadelphia L&I Yes: new insulation must meet new-construction R-value unless technically infeasible Technically infeasible (Philadelphia list): parapet heights and flashing limits, equipment curbs, window sills, door thresholds: match the existing R-value instead
Recover or tear-off decision compiled by CB&C from IBC Section 1512.3 (2025 California Building Code text), Philadelphia L&I PB_004 FAQ on IECC C503.2.1 (2021 code) and WSU bid results (2023); accessed November 1, 2026.
  1. Count the existing coverings. Two or more applications of any roof covering bar a recover under IBC Section 1512.3, as printed in the 2025 California Building Code.
  2. Scan for moisture. A water-soaked or deteriorated roof also bars a recover; WSU required a thermal scan before construction, and Columbus priced wet-area removal and replacement at $3.50 to $25.00 per sq ft in April 2026.
  3. Check the covering type. Slate, clay, cement or asbestos-cement tile bars a recover under the same section.
  4. On a tear-off that removes insulation entirely above the deck, install new insulation that meets the new-construction R-value, per IECC Section C503.2.1 as read by Philadelphia’s Department of Licenses and Inspections (2021 code FAQ); the R-value may never drop.
  5. Where parapet heights and flashing limits, equipment curbs, window sills or door thresholds make thicker insulation technically infeasible, Philadelphia permits matching the existing R-value instead.
Hidden condition found at tear-offUnit price rangeBidsDate, placeSource
Wet roof material removal and replacement, per sq ft$3.50 to $25.005Apr 2026, Columbus, GARFB 26-0033
Steel deck replacement, same gauge and profile, per sq ft$6.00 to $15.004Feb 2025, Penn StatePenn State OPP bid tab
Damaged 2.6 in polyiso replacement, per sq ft$2.50 to $10.004Feb 2025, Penn StatePenn State
3/4 in CDX plywood deck replacement, per sq ft$4.00 to $8.004Feb 2025, Penn StatePenn State
Cementitious wood fiber deck replacement, per sq ft$11.00 to $23.004Jul 2022, Columbus, GARFB 22-0041
Wood blocking and nailers, per board foot$2.00 to $12.005Apr 2026, Columbus, GARFB 26-0033

Unit prices like these cap the cost of surprises once the old roof is open, so ask for them on every bid form. If you are buying the building, the roof’s remaining life and immediate repair cost belong in the property condition assessment.

What does a worked TPO roof estimate look like?

A 20,000 sq ft tear-off with three 1.5-inch polyiso layers, a 1/2-inch cover board and 60-mil fully adhered TPO prices at $11.05 per sq ft from Tulsa’s 2023 contract medians, or $12.46 after escalation to September 2026 with the BLS roofing PPI. That is $249,200 before flashings, edge metal, drains and mobilization, which the April 2026 Columbus base bids include.

StepInput (source)Arithmetic$ per sq ft20,000 sq ft
1. Tear-off to deckMedian of $0.97, $0.97, $1.25 (Tulsa 2023)$0.97$0.97$19,400
2. Polyiso, three 1.5 in layers (R-27 by sum)Median $1.86 per layer (Tulsa 2023)3 x $1.86$5.58$111,600
3. Cover board, 1/2 in high-density fiberboard, fastenedMedian $1.25 (Tulsa 2023)$1.25$1.25$25,000
4. 60-mil TPO, fully adheredMedian $3.25 (Tulsa 2023)$3.25$3.25$65,000
5. Layer total, mid-2023Steps 1 to 40.97 + 5.58 + 1.25 + 3.25$11.05$221,000
6. Escalate to September 2026PPI 232.920 / 206.596 (Jun 2023) = 1.1274 (BLS)$11.05 x 1.1274$12.46$249,200
7. Compare with a complete base bidPop Austin median $15.50 (Columbus, Apr 2026)$15.50 minus $12.46$3.04 gap$60,800

The $3.04 per sq ft gap in step 7 is not itemized on either record. It is where perimeter flashing ($4.20 to $7.28 per sq ft of flashing membrane in Tulsa’s contract), edge metal, drains, permits, bonds and mobilization sit. Ask each bidder to break those lines out in a schedule of values.

How have TPO roofing prices moved since 2019?

Commercial roofing prices rose fast through 2023 and more slowly since. The BLS Producer Price Index for nonresidential roofing contractors averaged 136.9 in 2019 and 218.815 in 2025, a 59.8% rise, and the preliminary September 2026 reading of 232.920 is 5.7% above September 2025. Use it to update any roofing bid older than a year.

YearAnnual average index (Dec 2007 = 100)Change from prior yearSource
2019136.9Not applicableBLS PPI flat files
2020141.3+3.2%BLS
2021149.817+6.0%BLS
2022177.929+18.8%BLS
2023204.403+14.9%BLS
2024209.911+2.7%BLS
2025218.815+4.2%BLS
Producer price index, nonresidential roofing contractorsLine chart: the nonresidential roofing contractor PPI rose from 136.9 in 2019 to 177.929 in 2022, 204.403 in 2023 and 218.815 in 2025.120140160180200220240index2019202020212022202320242025
The nonresidential roofing contractor price index rose 59.8% from 2019 to 2025, with the steepest years in 2022 (+18.8%) and 2023 (+14.9%). Source: BLS PPI PCU23816X23816X, accessed November 1, 2026.

The index tracks what nonresidential roofing contractors charge, not TPO sheet prices alone, and BLS marks June to September 2026 values as preliminary. For the cross-trade picture, see our commercial construction price index, and for import duties on building materials, our tracker of construction material tariffs.

Which TPO option fits your roof?

Pick the scope in this order: code first (recover or tear-off), then insulation on a tear-off, then thickness and attachment. The thresholds below come from IBC Section 1512.3, IECC Section C503.2.1 as read by Philadelphia, the maker data sheets and the public bids above; each row says what to write into the bid documents and the price effect on the record.

IfThenPrice effect on the recordSource
Two or more coverings, a wet or deteriorated roof, or tileTear off to the deck$26.09 to $32.46 per sq ft replacement bids vs $8.82 recover (WSU 2023)IBC 1512.3; WSU
One dry covering and a sound deck on a moisture scanPrice a recover alternate next to the tear-offRecover at 33.8% of the lowest replacement bid (WSU 2023)WSU
Tear-off removes insulation entirely above the deckSpecify the new-construction R-value, or document technical infeasibility$1.75 to $1.90 per sq ft per 1.5 in polyiso layer (Tulsa 2023)Philadelphia L&I; Tulsa
Roof under 3,500 sq ftBudget a higher per-sq-ft price than for a large roof$28.64 to $44.05 (2022) vs $11.76 to $18.93 on 12,500 sq ft and up (2026)Columbus
Regular foot traffic to rooftop units, or hail exposureSpecify 80 mil and name the product line80-mil EXTRA watertight at 30.0 J vs 22.5 J for 60 milCarlisle
Warranty term is the goal, not puncture resistance60 mil can carry the same term as 80 milDuro-TECH 15, 20 or 25 years at both thicknessesDuro-Last
Bid or estimate older than 12 monthsEscalate with the roofing PPI+5.7% from Sep 2025 to Sep 2026 (preliminary)BLS

Where do cost guides and the bid record disagree?

Most consumer cost guides quote membrane-layer prices as if they were finished roofs. The public record separates the two: Tulsa’s 2023 contract priced the 60-mil fully adhered sheet alone at $3.00 to $3.27 per sq ft, while complete Columbus re-roof bids in April 2026 ran $11.76 to $18.93. Four common claims are compared with the primary record below.

What a cost guide saysWhat the primary record showsSource
A top-ranking guide updated September 2026: 60-mil TPO costs $4.00 to $6.50 per sq ft installedThe 60-mil membrane line alone was $3.00 to $3.27 (Tulsa 2023); complete re-roof bids were $11.76 to $18.93 (Columbus 2026)Tulsa; Columbus
A guide updated January 2026: 80 mil adds $0.30 to $0.35 per sq ft over 60 milNone of the 11 public records we compiled prices the difference; treat the figure as an unsourced estimateCB&C review, Nov 2026
Several guides: tear-off adds $1 to $2 per sq ftConsistent: $0.97 to $1.25 per sq ft (Tulsa 2023)Tulsa
Several guides: 60-mil warranties run 15 to 20 yearsDuro-Last lists 15, 20 and 25-year options for 60-mil Duro-TECH (2024)Duro-Last

For every low-slope system side by side, including EPDM, PVC, modified bitumen and coatings, see our flat roof replacement cost guide.

How we compiled this

We read 7 public bid tabulations and contract price sheets (Columbus, Georgia; Tulsa, Oklahoma; Washington State University; Penn State), 4 federal award records from USAspending.gov, 4 TPO maker data sheets, 1 NRCA technical article, 2 code texts and the BLS PPI flat file, all accessed in November 2026. Prices are each agency’s figures divided by the roof area printed on the same record; bids without a stated area or a confirmed TPO scope were excluded. CB&C is a matching service, not a roofer, and nothing here is a quote.

Frequently asked questions

How much does a 10,000 sq ft TPO roof cost?

At the April 2026 Columbus, Georgia bid range of $11.76 to $18.93 per sq ft, a 10,000 sq ft TPO re-roof works out to $117,600 to $189,300. That range comes from roofs of 12,500 to 17,500 sq ft; smaller roofs bid higher per sq ft, such as $31.29 to $37.96 on 9,100 to 10,400 sq ft in Columbus in July 2022.

How much does TPO roofing cost per square?

A roofing square is 100 sq ft. The five April 2026 Columbus, Georgia bids equal $1,176 to $1,893 per square for a complete TPO re-roof, with a median of $1,550. The membrane line alone in Tulsa’s 2023 roofing contract was $300 to $327 per square for 60-mil fully adhered TPO, before insulation, cover board and tear-off.

Is TPO cheaper than EPDM?

On the same City of Tulsa 2023 roofing contract, 60-mil fully adhered TPO was priced at $3.00 to $3.27 per sq ft and 60-mil fully adhered EPDM at $3.75 to $4.19 across three bids, so TPO was $0.75 to $0.92 lower per sq ft on the membrane line. Insulation, cover board and tear-off cost the same under either sheet.

How long does a TPO roof last?

No public record we compiled measures service life, so warranty terms are the documented benchmark. Duro-Last lists 15, 20 and 25-year warranties for its 60 and 80-mil Duro-TECH sheets (October 2024), and Johns Manville’s 2016 JM TPO 80 sheet lists Peak Advantage guarantees of 5 to 30 years. The term depends on the full system specified, not the sheet alone.

Can TPO be installed over an existing roof?

Yes, where the building code allows a recover. IBC Section 1512.3 bars a recover if the existing roof is water-soaked or deteriorated, is slate, clay, cement or asbestos-cement tile, or already has two or more coverings. Washington State University recovered 32,200 sq ft with mechanically fastened 115-mil TPO fleeceback for $284,000 in 2023, after requiring a thermal scan.

How long does a TPO roof installation take?

Bidders on the April 2026 Pop Austin Recreation Center job in Columbus, Georgia, measured at 12,500 to 17,500 sq ft, estimated 14 to 120 working days with average crews of 6 to 12 people. Their start dates ranged from 21 to 100 days after notice to proceed, so material lead time can matter as much as installation time.

Sources

Bid tabulations, awards and price data

Maker data sheets, standards and codes

Last reviewed November 2026 by the CB&C Editorial Team. See our editorial standards.

← Back to all articles