Commercial handrail height is 34 to 38 inches, measured vertically from the stair nosing line or ramp surface to the top of the rail, and guards at drops over 30 inches must be at least 42 inches high.
Key takeaways
- Handrails on commercial stairs and ramps sit 34 in minimum and 38 in maximum above the tread nosings or ramp surface, at a uniform height (IBC Section 1014.2, confirmed in the 2022 NYC Building Code text).
- A guard is required where an open side is more than 30 in above the floor or grade within 36 in of the edge, and it must be at least 42 in high (IBC 1015.2 and 1015.3, Washington WAC 51-50-1015).
- The 2010 ADA Standards repeat the 34 to 38 in range in Section 505.4 and add both-side rails, 12 in extensions, a 1-1/4 to 2 in round grip and 1-1/2 in wall clearance.
- OSHA allows a guardrail top edge of 42 in plus or minus 3 in, so 39 to 45 in, under 29 CFR 1910.29(b)(1) for workplaces and 29 CFR 1926.502(b)(1) for construction sites.
- OSHA handrails are 30 to 38 in in general industry but 30 to 37 in on construction stairs (29 CFR 1926.1052(c)(6)), so a 34 to 38 in building-code rail passes general industry but must be held at 37 in or less on stairs used during construction.
- Nine federal handrail contracts from 2021 to 2026 ranged from $4,583 to $123,510, a median of $17,134 (USAspending.gov, pulled November 8, 2026).
What is the required handrail height on a commercial stair or ramp?
The required handrail height on a commercial stair or ramp is 34 in minimum to 38 in maximum, measured straight up from the line connecting the tread nosings, or from the finished ramp surface, to the top of the rail. Section 1014.2 of the International Building Code (IBC, the model code most states adopt for commercial buildings) also says the height must be uniform along the flight.
The IBC Chapter 10 sets the rule for every stair and ramp in a commercial building, and the U.S. Department of Justice’s 2010 ADA Standards set the same 34 to 38 in range for stairs and ramps in places of public accommodation. Two numbers trip owners most: the rail is measured at the nosing line, not at the back of the tread, and the guard on an open side is a separate 42 in element. The table holds every key dimension; the numbered callouts in the stair drawing below match its rows.
| Element | Commercial number | Measured from or applies to | Source |
|---|---|---|---|
| 1. Handrail height | 34 in min, 38 in max, uniform | Nosing line on stairs; ramp surface on ramps | IBC 1014.2; ADA 505.4 |
| 2. Guard height | 42 in min | Walking surface; nosing line on stairs | IBC 1015.3 |
| Guard trigger | Drop over 30 in within 36 in horizontally | Open sides of floors, stairs, ramps, landings, mezzanines, platforms | IBC 1015.2 |
| 3. Top extension, stair | 12 in horizontal min | Beyond the top riser | IBC 1014.6; ADA 505.10.2 |
| 4. Bottom extension, stair | One tread depth at the stair slope | Beyond the bottom riser | IBC 1014.6; ADA 505.10.3 |
| Ramp extensions | 12 in horizontal min, top and bottom | Beyond each ramp run | IBC 1014.6; ADA 505.10.1 |
| 5. Guard openings | 4 in sphere to 36 in; 4-3/8 in sphere from 36 to 42 in | Whole guard height | IBC 1015.4 |
| 6. Stair triangle | 6 in sphere | Opening at riser, tread and bottom rail | IBC 1015.4 Exception 2 |
| Rails on stairs | Both sides | Every stairway, with dwelling-unit and spiral exceptions | IBC 1011.11; ADA 505.2 |
| Rails on ramps | Both sides when rise is over 6 in | Each ramp run | IBC 1012.8; ADA 405.8 |
| Intermediate handrail | All required width within 30 in of a rail | Wide stairs | IBC 1014.9 |
| Round grip | 1-1/4 in to 2 in outside diameter | Gripping surface | IBC 1014.3.1; ADA 505.7.1 |
| Non-round grip | Perimeter 4 to 6-1/4 in, cross section 2-1/4 in max | Gripping surface | IBC 1014.3.1; ADA 505.7.2 |
| Wall clearance | 1-1/2 in min | Rail to wall or other surface | IBC 1014.7; ADA 505.5 |
| Projection into width | 4-1/2 in max each side | At or below handrail height | IBC 1014.8 |
The 2021 IBC section numbers above are the ones most jurisdictions enforce as of November 2026; New York City’s 2022 code and Washington’s WAC 51-50-1014 reproduce the same 34 to 38 in text with local amendments. Stair geometry (riser height, tread depth, headroom) is a separate rule set that our sibling guide on stair riser height covers, and it does not change the rail heights.
How high must a guardrail be, and when is one required?
A commercial guardrail must be at least 42 in high wherever a walking surface is more than 30 in above the floor or grade below, measured at any point within 36 in horizontally of the open edge (IBC 1015.2 and 1015.3). On a stair the 42 in is measured from the nosing line; on a ramp, from the ramp surface at the guard.
Openings are the second half of the rule. A 4 in sphere may not pass anywhere from the walking surface up to 36 in, a 4-3/8 in sphere may not pass between 36 and 42 in, and the triangle under the bottom rail of an open stair may pass up to a 6 in sphere (IBC 1015.4). Areas closed to the public get relief: guards at equipment access surfaces and in non-public parts of Group I-3, F, H and S buildings only have to stop a 21 in sphere.
| Rule | IBC (building) | OSHA 1910 (workplace) | OSHA 1926 (construction) | Source |
|---|---|---|---|---|
| Height | 42 in min | 42 in plus or minus 3 in; over 45 in allowed | 42 in plus or minus 3 in | IBC 1015.3; 1910.29(b)(1); 1926.502(b)(1) |
| When required | Drop over 30 in | Drop of 4 ft or more | Drop of 6 ft or more | IBC 1015.2; 1910.28(b)(1); 1926.501(b)(1) |
| Infill | 4 in sphere to 36 in; 4-3/8 in from 36 to 42 in | Midrail at mid-height, or openings 19 in max | Midrail at mid-height, or openings 19 in max | IBC 1015.4; 1910.29(b)(2); 1926.502(b)(2) |
| Strength | IBC 1607 structural load | 200 lb on top rail; may not deflect below 39 in | 200 lb on top rail; may not deflect below 39 in | 1910.29(b)(3), (b)(4); 1926.502(b)(3), (b)(4) |
| Equipment near an edge | Guard if equipment or roof hatch is within 10 ft of an edge over 30 in high | Fall protection at 4 ft | Fall protection at 6 ft | IBC 1015.6, 1015.7 |
The building code number is the one a plan reviewer and inspector check before the certificate of occupancy. OSHA’s numbers govern the employer’s duty to protect workers on that surface afterward, and the construction-site version applies while the building is going up. The duty-to-have-fall-protection rule (29 CFR 1926.501) was the most cited standard for nonresidential building contractors in fiscal 2024, with 163 citations, in our research on OSHA violations in commercial construction.
Handrail or guard: can one rail do both jobs?
On a commercial stair, no: the guard on an open side must reach 42 in, while the handrail must stay between 34 and 38 in, so the open side carries two rails, usually a handrail bracketed to the guard posts. One rail can do both jobs only where a code section allows a lower guard, as listed below.
| Setting | One rail allowed? | Height of the combined rail | Source |
|---|---|---|---|
| Commercial stair, open side | No: guard plus separate handrail | Guard 42 in min; handrail 34 to 38 in | IBC 1015.3, 1014.2 |
| Inside a Group R-2 dwelling unit or a Group R-3 building | Yes | 34 to 38 in from the nosing line | IBC 1015.3 exception |
| Alternating tread device or ship’s ladder | Yes | 30 to 34 in | IBC 1015.3 exception |
| Group F exit access stair serving fewer than 3 stories, not public (Washington adoption) | Yes | 34 to 38 in | WAC 51-50-1015 Exception 7 |
| General industry stair, OSHA only | Yes | 36 to 38 in | 1910.29(f)(1)(iii) |
| Construction stair, OSHA only | Yes | 36 to 37 in | 1926.1052(c)(7) |
The occupancy group decides which row applies, so confirm it on the code analysis sheet before the rail is detailed; our guide to occupancy classification explains the Group F, R-2 and R-3 labels used here.
What do the ADA Standards add to the building code?
The 2010 ADA Standards use the same 34 to 38 in height but measure it to the top of the gripping surface, and they add rules on continuity, bottom obstructions and children’s rails. The ADA applies to stairs that are part of a means of egress (Section 210.1) and to ramp runs rising more than 6 in (Section 405.8).
| Element | 2010 ADA Standards | IBC | What differs |
|---|---|---|---|
| Height | 34 to 38 in to top of gripping surface (505.4) | 34 to 38 in above nosings or ramp surface (1014.2) | Nothing |
| Stairs covered | Stairs in a means of egress (210.1) | Every stairway (1011.11) | IBC covers more stairs |
| Ramps covered | Rise over 6 in (405.8) | Rise over 6 in (1012.8) | Nothing |
| Sides | Both sides (505.2); one rail allowed on assembly aisle ramps | Both sides (1011.11, 1012.8) | Assembly aisle exception |
| Bottom of rail | Obstructed for no more than 20% of its length (505.6) | Brackets allowed within 1-1/2 in below the rail (1014.4) | ADA caps total obstruction |
| Ramp edge protection | 12 in extended surface or curb stopping a 4 in sphere within 4 in of the surface (405.9) | 4 in curb or 12 in extended surface (1012.10) | Nothing material |
| Children | Second rail 28 in max, 9 in min gap, recommended only (Advisory 505.4) | No rule | Advisory, not mandatory |
| Alterations | Full extensions not required where hazardous (505.10 Exception 3) | No matching exception | ADA relief in tight retrofits |
| Altered stairs between levels on an accessible route | 505 rails required when the stair is altered (210.1 Exception 2) | Code for the alteration | Rails follow alteration scope |
Ramp slope, landings and edge protection sit in Section 405 and are covered in our guide to ADA ramp requirements. For an office or retail fit-out, the rail work usually falls inside the 20% path-of-travel budget discussed in our office renovation cost guide.
How does OSHA set handrail and guardrail height?
OSHA sets guardrails at 42 in plus or minus 3 in in both its general industry and construction rules, but the handrail and stair rail numbers differ between the two. General industry (29 CFR 1910) covers stairs workers use in an operating building; construction (29 CFR 1926) covers stairs and edges during the build.
| Item | General industry, 29 CFR 1910 | Construction, 29 CFR 1926 |
|---|---|---|
| Guardrail height | 42 in plus or minus 3 in (1910.29(b)(1)) | 42 in plus or minus 3 in (1926.502(b)(1)) |
| Fall height that triggers protection | 4 ft (1910.28(b)(1)) | 6 ft (1926.501(b)(1)) |
| Stair needs rails when | 3 or more treads and 4 or more risers (1910.28(b)(11)(ii)) | 4 or more risers or more than 30 in of rise (1926.1052(c)(1)) |
| Handrail height | 30 to 38 in from the leading edge of the tread (1910.29(f)(1)(i)) | 30 to 37 in (1926.1052(c)(6)) |
| Stair rail height | 42 in min if installed on or after January 17, 2017; 30 in min if earlier (1910.29(f)(1)(ii)) | 36 in min if installed after March 15, 1991 (1926.1052(c)(3)) |
| Stair rail used as handrail | 36 to 38 in (1910.29(f)(1)(iii)) | 36 to 37 in (1926.1052(c)(7)) |
| Hand clearance | 2.25 in min (1910.29(f)(2)) | 3 in min for temporary handrails (1926.1052(c)(11)) |
| Openings | 19 in max (1910.29(f)(4)) | 19 in max (1926.1052(c)(4)) |
| Strength | 200 lb (1910.29(f)(7)) | 200 lb (1926.1052(c)(5)) |
The number of rails on a workplace stair depends on width under Table D-2 of 29 CFR 1910.28: a stair under 44 in wide needs at least one handrail, a stair 44 to 88 in wide needs a handrail on each enclosed side and a stair rail on each open side, and a stair over 88 in wide also needs one intermediate handrail. Our construction safety guide sets these rules against injury data for the trades.
Where do handrails start and stop?
Handrails run continuously along each flight, then extend 12 in horizontally past the top riser and continue at the stair slope for one tread depth past the bottom riser; on ramps they extend 12 in horizontally at both ends (IBC 1014.6; ADA 505.10). Each end returns to a wall, guard or the floor, or joins the next flight.
| Location | Extension | Exception | Source |
|---|---|---|---|
| Top of stair flight | 12 in horizontal, starting above the top riser nosing | None for continuous inside rails at switchbacks | IBC 1014.6; ADA 505.10.2 |
| Bottom of stair flight | Slope continues for one tread depth past the bottom riser nosing | Same | IBC 1014.6; ADA 505.10.3 |
| Ramp run, top and bottom | 12 in horizontal above the landing | Same | IBC 1014.6; ADA 505.10.1 |
| Inside turn of a switchback or dogleg | None if the rail is continuous | Continuous rail replaces extension | ADA 505.10 Exception 1 |
| Alteration with no room | Full extension may be shortened | Only where the extension would be hazardous | ADA 505.10 Exception 3 |
| End of rail | Return to wall, guard or walking surface | Or continue to adjacent flight | IBC 1014.6; ADA 505.10 |
The return matters because an open rail end can catch a sleeve or a bag strap. A bottom extension that stops in a corridor also projects into the egress path, so the plan should show where each extension lands before steel is ordered; IBC 1014.8 limits projections into the required width to 4-1/2 in on each side at or below handrail height.
How do residential rules differ?
Residential rules under the International Residential Code (IRC) keep the same 34 to 38 in handrail height but require a rail on only one side and a lower guard. They apply to one- and two-family houses and townhouses, not to commercial buildings, so treat this table as a contrast only.
| Item | Commercial (IBC) | Residential (IRC, labelled contrast) | Source |
|---|---|---|---|
| Handrail height | 34 to 38 in | 34 to 38 in | IBC 1014.2; IRC R311.7.8.1 |
| Handrails required | Both sides of every stair | One side, on flights with 4 or more risers | IBC 1011.11; IRC R311.7.8 |
| Guard height | 42 in | 36 in model code; California raises it to 42 in | IBC 1015.3; IRC R312.1.2; City of Alameda handout |
| Guard on open stair sides | 42 in from nosing line | 34 in from nosing line | IBC 1015.3; IRC R312.1.2 |
| Guard trigger | Over 30 in within 36 in | Over 30 in within 36 in | IBC 1015.2; IRC R312.1.1 |
| Openings | 4 in sphere to 36 in; 4-3/8 in above | 4 in sphere; 4-3/8 in on stair sides | IBC 1015.4; IRC R312.1.3 |
A mixed-use building with apartments over retail follows the IBC everywhere, including the residential floors; only the space inside each dwelling unit gets the Group R-2 exceptions listed in IBC 1015.3.
Which rule applies to my project?
Start with the drop at each open side, then the stair or ramp, then accessibility and workplace use: each yes adds a requirement, and where two rules overlap the stricter number governs. The table gives the thresholds; the flowchart shows the same order.
| If | Then | Source |
|---|---|---|
| An open side is more than 30 in above the floor or grade within 36 in | Install a 42 in guard that stops a 4 in sphere to 36 in | IBC 1015.2 to 1015.4 |
| The element is a commercial stair | Handrails both sides at 34 to 38 in, with 12 in top and one-tread bottom extensions | IBC 1011.11, 1014.2, 1014.6 |
| The stair is wider than 60 in of required width | Add an intermediate handrail so all required width is within 30 in of a rail | IBC 1014.9 |
| A ramp rises more than 6 in | Handrails both sides at 34 to 38 in with 12 in extensions | IBC 1012.8; ADA 405.8 |
| A ramp rises 6 in or less | No handrails required | ADA 405.8; IBC 1012.8 |
| An existing rail measures under 34 in or over 38 in | Out of range for new work; reset or replace when that stair is altered | IBC 1014.2; ADA 210.1 Exception 2 |
| An existing guard is 36 in in a commercial space | Below 42 in; ask the building official whether your alteration scope requires an upgrade | IBC 1015.3 |
| The surface is a non-public equipment platform | Guard openings may be up to a 21 in sphere; OSHA midrail still applies | IBC 1015.4 Exception 3; 1910.29(b)(2) |
| Children are the main users | Consider a second rail at 28 in max with 9 in gap | ADA Advisory 505.4 |
| Workers build or use a temporary stair | Handrail 30 to 37 in; stair rail 36 in min; guard 42 in plus or minus 3 in at 6 ft | 1926.1052(c); 1926.502(b) |
How do you check an existing handrail in the field?
A field check takes a tape, a level, a 4 in and a 4-3/8 in test ball (or a cut pipe of that diameter) and about 10 minutes per flight. Record each reading by flight so failures go straight onto a punch list.
- Stretch a string or straightedge across three nosings and measure vertically from it to the top of the handrail at the top, middle and bottom of the flight; each reading must fall between 34 and 38 in and match the others (IBC 1014.2).
- On ramps, measure from the ramp surface to the top of the rail at both ends and mid-run; same 34 to 38 in range (ADA 505.4).
- Measure the guard on every open side: 42 in min from the walking surface, or from the nosing line on stairs (IBC 1015.3). Measure from the top of any fixed bench or planter within 21 in if your jurisdiction follows the New York City text.
- Push the 4 in ball through the guard below 36 in and the 4-3/8 in ball between 36 and 42 in; check the stair triangle with a 6 in ball (IBC 1015.4).
- Measure the top extension (12 in horizontal past the top riser) and bottom extension (one tread depth at slope) and confirm the ends return (IBC 1014.6).
- Measure grip diameter with calipers: 1-1/4 to 2 in round, or 4 to 6-1/4 in perimeter for shaped rails (IBC 1014.3.1).
- Measure clearance to the wall: 1-1/2 in min (IBC 1014.7); confirm the rail does not rotate in its fittings (IBC 1014.5; ADA 505.9).
- Measure stair width between rails; if any part of the required width is more than 30 in from a rail, an intermediate rail is missing (IBC 1014.9).
- For workplace stairs, apply a firm downward and outward push and look for movement at posts; the design load is 200 lb (1910.29(f)(7)), which a structural engineer verifies by calculation, not by hand.
Log failures with location, measurement and section so the contractor prices each one; our guide to the construction punch list shows the format, and an inspector will check the same items before issuing a certificate of occupancy.
What does it cost to add or replace a commercial handrail?
Installed aluminum handrail on a 2026 City of Tampa sidewalk contract was bid at $85 to $300 per linear foot by four bidders, and nine federal handrail jobs from 2021 to 2026 ran $4,583 to $123,510 per contract. Length, finish, anchoring into concrete and whether a 42 in guard is also needed move the total most.
| Bid item (City of Tampa, contract 26-C-00023, bids opened August 18, 2026) | Quantity | Unit prices from 4 bidders | Source |
|---|---|---|---|
| Aluminum handrail, FDOT Index 870, 2-rail (installed) | 20 LF | $85, $130, $160, $300 per LF | City of Tampa bid tabulation |
| Aluminum handrail, FDOT Index 860, picket style (installed) | 20 LF | $85, $145, $160, $300 per LF | Same |
| Temporary handrail | 100 LF | $1, $5, $5, $45 per LF | Same |
FDOT Index 870 and 860 are Florida Department of Transportation standard rail drawings for pedestrian rail; the picket version adds vertical infill like a guard. These are exterior sidewalk prices in Tampa for small quantities, so treat them as a floor-level reference, not a building-interior quote.
| Federal contract (USAspending.gov) | Signed | Award | Award ID |
|---|---|---|---|
| Replace handrails, federal building, Brunswick, GA | Aug 2024 | $123,510 | 47PE0224F0156 |
| Install handrails, west side stairs, Memorial Building, national historical park, Hodgenville, KY | Aug 2022 | $89,851 | 140P5122P0122 |
| Exterior handrails replacement, federal building, Wichita, KS | Mar 2022 | $61,486 | 47PG0522F0015 |
| Install handrail, 4th floor and gym emergency exit, federal building, Birmingham, AL | Aug 2026 | $34,261 | 47PE5526F0621 |
| Install handrail, generator platform, U.S. courthouse, Knoxville, TN | May 2026 | $17,134 | 47PE5526F0224 |
| Replace handrails, north side of a federal building, Washington, DC | Jun 2021 | $10,742 | 47PM0121F0023 |
| Replace handrail, museum loading dock, Chantilly, VA | Apr 2022 | $9,121 | 33313222P00473342 |
| Fabricate and install handrail, building entrance, federal center, Lakewood, CO | May 2025 | $4,826 | 47PJ0025C0024 |
| Entrance step handrail replacement, federal building, Battle Creek, MI | Sep 2024 | $4,583 | 47PF0024F1019 |
None of the nine award records states rail length, so the per-contract spread reflects scope, not a unit price. Hospital-scale programs run higher: two Department of Veterans Affairs handrail replacement contracts were $539,429 (Waco VA medical center, June 2025, 25 offers) and $1,015,120 (Coatesville VA medical center, August 2023).
The worked example below prices rails for one stair flight and one ramp run with the Tampa unit prices. It shows how extensions add length that a quick plan takeoff misses.
| Step | Stair: 10 risers, 7 in rise, 11 in tread | Ramp: 30 in rise at 1:12 |
|---|---|---|
| Horizontal run of the rail between ends | 9 treads x 11 in = 99 in | 30 in x 12 = 360 in |
| Vertical rise along the rail | 9 risers x 7 in = 63 in | 30 in |
| Sloped rail length | 117.3 in | 361.2 in |
| Extensions | 12 in top + 13.0 in sloped bottom (one 11 in tread) | 12 in top + 12 in bottom |
| Length per side | 142.4 in = 11.9 ft | 385.2 in = 32.1 ft |
| Both sides, rounded | 24 LF | 64 LF |
| At $85 to $300 per LF (Tampa, 2026) | $2,040 to $7,200 | $5,440 to $19,200 |
Add a 42 in guard on any open side above 30 in, plus core drilling, patching and finishes for interior work. Ask each bidder to price rail per linear foot with extensions and returns shown, so the bids line up the way our guide on comparing construction bids describes.
What do guides get wrong about handrail height?
Most errors come from mixing the building code with OSHA, or carrying an older edition’s sphere and extension rules into a current project, and each one changes what a contractor fabricates. The table sets six claims found in top-ranking guides and one government handout against the primary text as of November 2026.
| What some guides say | What the primary source says | Source |
|---|---|---|
| “OSHA handrail height is 30 to 38 in” (applied to every site) | 30 to 38 in in general industry, 30 to 37 in on construction stairs; neither replaces the IBC 34 to 38 in for new buildings | 1910.29(f)(1)(i); 1926.1052(c)(6) |
| “OSHA guardrails must be exactly 42 in” | 42 in plus or minus 3 in, so 39 to 45 in, and higher is allowed if other criteria are met | 1910.29(b)(1); 1926.502(b)(1) |
| “The ADA requires 42 in guardrails” | ADA Section 505 covers handrails only; the 42 in guard comes from IBC 1015.3 and OSHA | ADA 505; IBC 1015.3 |
| “4-3/8 in sphere above 34 in” (a county stair handout labelled IBC 2018) | The 4-3/8 in sphere applies from 36 to 42 in | IBC 1015.4 Exception 1; Humboldt County handout |
| “Extend the rail 12 in beyond the bottom riser” (same handout) | Continue at the stair slope for one tread depth past the bottom riser | IBC 1014.6; ADA 505.10.3 |
| “A 28 in children’s rail is required” | Recommended in an advisory note, not required | ADA Advisory 505.4 |
The stair geometry the handrail follows, risers, treads and landings, is set out in our stair riser height guide.
How we compiled this
We compiled this page in November 2026 from 17 primary documents: the 2010 ADA Standards, five OSHA sections read in the eCFR (current to November 5, 2026), the 2022 New York City and Washington State reproductions of the 2021 IBC (the ICC viewer blocks automated reads), the IRC, a City of Tampa bid tabulation and nine USAspending.gov award records. Prices are public bids and awards, not quotes we requested, and CB&C calculations are labelled. This page is not legal or engineering advice; confirm the code edition and local amendments with your building department.
Frequently asked questions
What is the standard handrail height for commercial stairs?
Commercial stair handrails must be 34 to 38 in high, measured vertically from the line connecting the tread nosings to the top of the rail, and uniform along the flight under IBC Section 1014.2. The 2010 ADA Standards use the same range in Section 505.4. Stairs need rails on both sides, plus a 42 in guard on any open side above 30 in.
Is handrail height measured from the nose of the step?
Yes. On stairs, handrail height is measured vertically from the sloped line that connects the leading edges of the tread nosings, not from the back of the tread (IBC 1014.2, ADA 505.4). OSHA uses the same point, the leading edge of the tread (1910.29(f)(1)(i)). On ramps, measure from the finished ramp surface.
What is the difference between a handrail and a guardrail?
A handrail is the rail you grip, 34 to 38 in high with a 1-1/4 to 2 in round profile (IBC 1014). A guard, or guardrail, stops falls from an open side more than 30 in above the floor below; it is at least 42 in high and stops a 4 in sphere up to 36 in (IBC 1015). Commercial open stairs usually need both.
What is the OSHA requirement for handrail height?
OSHA general industry rules set handrails at 30 to 38 in from the leading edge of the tread (29 CFR 1910.29(f)(1)(i)); construction stairs use 30 to 37 in (29 CFR 1926.1052(c)(6)). OSHA guardrails are 42 in plus or minus 3 in. A new commercial stair also has to meet the building code range of 34 to 38 in.
Do commercial stairs need handrails on both sides?
Yes. IBC Section 1011.11 requires handrails on each side of a stairway, with exceptions for stairs inside dwelling units and spiral stairs, and ADA 505.2 requires both sides for covered stairs and ramps. Stairs wide enough that part of the required width is over 30 in from a rail also need an intermediate handrail (IBC 1014.9).
How high does a guardrail need to be on a commercial building?
At least 42 in, measured from the walking surface, or from the nosing line on stairs (IBC 1015.3), wherever the open side is more than 30 in above the floor or grade within 36 in horizontally. Inside Group R-2 dwelling units and R-3 buildings, the open sides of stairs may drop to 34 in.
Sources
- International Building Code 2024, Chapter 10 Means of Egress (International Code Council), accessed 2026-11-08
- 2022 NYC Building Code, Chapter 10 Means of Egress (NYC Department of Buildings), accessed 2026-11-08
- WAC 51-50-1014 Handrails (Washington State Legislature), accessed 2026-11-08
- WAC 51-50-1015 Guards (Washington State Legislature), accessed 2026-11-08
- 2010 ADA Standards for Accessible Design (Sections 210, 405, 505) (U.S. Access Board), accessed 2026-11-08
- 2010 ADA Standards for Accessible Design (U.S. Department of Justice), accessed 2026-11-08
- 29 CFR 1910.29 Fall protection systems criteria (eCFR), accessed 2026-11-08
- 29 CFR 1910.28 Duty to have fall protection, Table D-2 (eCFR), accessed 2026-11-08
- 29 CFR 1926.501 Duty to have fall protection (eCFR), accessed 2026-11-08
- 29 CFR 1926.502 Fall protection systems criteria (eCFR), accessed 2026-11-08
- 29 CFR 1926.1052 Stairways (eCFR), accessed 2026-11-08
- International Residential Code 2021, Chapter 3 (International Code Council), accessed 2026-11-08
- Guardrails and Handrail Requirements (City of Alameda, CA), accessed 2026-11-08
- Contract 26-C-00023 itemized bid tabulation (City of Tampa), accessed 2026-11-08
- Federal contract award records (11 awards) (USAspending.gov), accessed 2026-11-08
- Stairway and landing requirements for commercial buildings (IBC 2018) (Humboldt County, NV), accessed 2026-11-08
