Skip to content

Polished Concrete Cost per Square Foot: Commercial Bid Prices by Scope

Empty retail shell with a polished gray concrete floor reflecting storefront daylight

Commercial polished concrete cost $6.92 to $16.06 per sq ft in five 2021 to 2026 public awards that removed old flooring first, and $3.92 to $4.11 per sq ft on bare slabs in 2010 and 2018 federal awards.

Key takeaways

How much does polished concrete cost per square foot?

Polished concrete cost $6.92 to $16.06 per sq ft installed in five public awards from 2021 to 2026 that included tearing out carpet, laminate, vinyl or an old coating. Bare slabs with nothing to remove cost $3.92 (2018) and $4.11 (2010). Restated with the BLS concrete contractor price index, the full set spans $6.14 to $18.10 per sq ft in September 2026 dollars.

Those figures are award or bid totals divided by the area each owner published, so they include mobilization, labor, diamonds, densifier, guard and, where stated, cove base. Residential cost pages quote $2 to $16 per sq ft without naming a job; the public records below name the room, the grit sequence and the date.

ScopePrice per sq ft (as awarded)In Sept 2026 dollarsRecordSource
Bare slab, nothing to remove, 2,526 to 27,000 sq ft$3.92 to $4.11$6.14 to $7.81USACE CRREL 2018; GSA El Paso courthouse 2010SAM.gov award notices
Carpet or vinyl removed, 3,100 to 4,900 sq ft, 400 to 800 grit$6.92 to $7.40$7.31 to $7.52JBER 2025; Fresno ANG 2026USAspending.gov
Carpet and laminate removed, 5,600 sq ft, plus sound panels$12.48 to $14.72 (3 bids)$17.22 to $20.31City of Madera 2021Madera council report
Epoxy or coating ground off, 1,000 to 2,405 sq ft$13.80 to $16.06$15.41 to $18.10Fresno ANG 2024; GSA St. Louis 2022USAspending.gov, SAM.gov

What did public owners actually pay for polished concrete?

Seven public records from 2010 to 2026 give both a dollar amount and a floor area, which is what a cost per square foot needs. Six are federal awards found on USAspending.gov and SAM.gov, and one is a city bid opening in California. Each row shows the scope the owner wrote, because removal, grit level and room size explain most of the spread.

Owner, place, dateAreaScope written in the solicitationAmountPer sq ftSept 2026 dollarsSource
GSA, new U.S. Courthouse, El Paso TX, May 201027,000 sq ftHone, grind and polish exposed slab in public areas; densifier$111,043$4.11$7.81GS-07P-10-HH-C-0020
USACE CRREL, Hanover NH, June 20182,526 sq ftGrind 50 grit, repair cracks, potassium densifier, 800 grit, seal, burnish$9,900$3.92$6.14W912HZ18P0074
City of Madera police building, CA, bids June 10, 20215,600 sq ft (5,400 polished, 200 bare)Remove carpet and laminate, sand and polish slab, add sound panels$69,900 low bid$12.48$17.22IFB 202021-07
GSA, Robert A. Young Federal Building, St. Louis MO, July 20222,405 sq ftStrip coatings, 40 to 200 grit metal, dye, densifier x2, 800, 1500, 2000 grit resin$38,617.53$16.06$18.1047PG0322F0046
Air National Guard, Fresno CA, Feb 20241,000 sq ftRemove epoxy, densify, 800 grit, non-skid guard, 1,000 LF cove base$13,800$13.80$15.41W50S6T24P0005 (terminated for default)
Air Force, JBER, Anchorage AK, Sept 20253,100 sq ftRemove carpet and adhesive, fill cracks and joints, 400 grit, stain, 2 guard coats, cove base$21,445 (16 offers)$6.92$7.31FA500025P0108
Air National Guard, Fresno CA, June 20264,900 sq ft densified and guardedRemove 1,260 sq ft vinyl and carpet, 40 to 800 grit, lithium densifier, guard with traction additive, mock-ups$36,280 (18 offers)$7.40$7.52W50S6T26CA012
Public polished concrete awards per sq ft, as awarded and in Sept 2026 dollarsBar chart: seven public polished concrete awards from $3.92 to $16.06 per sq ft, $6.14 to $18.10 in 2026 dollars$ per sq ftCRREL bare slab, 2,526 sq ft (2018)3.92El Paso new slab, 27,000 sq ft (2010)4.11JBER carpet out, 3,100 sq ft (2025)6.92Fresno vinyl out, 4,900 sq ft (2026)7.4Madera carpet out, 5,600 sq ft (2021)12.5Fresno epoxy out, 1,000 sq ft (2024)13.8GSA coatings out, 2000 grit, 2,405 sq ft (16.1
Jobs that removed a coating on 2,405 sq ft or less cost about twice the per-foot price of 3,100 to 4,900 sq ft carpet-removal jobs. Sources: USAspending.gov, SAM.gov, City of Madera, BLS PPI, accessed November 9, 2026.

The City of Madera bid is the only one of the seven with every bidder’s price published. Three firms bid on June 10, 2021: $69,900, $76,679 and $82,439.25, a spread of $12.48 to $14.72 per sq ft. The April 20, 2022 council report says the work covered removing carpet and laminate tile, sanding the slab and polishing it, plus sound-deadening panels to offset the echo a polished floor creates.

Madera council report with 5,400 sq ft polished area and three bids of $69,900 to $82,439.25 boxed
City of Madera report to City Council, April 20, 2022, item B-10: about 5,400 ft2 to be polished and 200 ft2 left bare; bids of $69,900.00, $76,679.00 and $82,439.25 opened June 10, 2021. Bidder names removed. Archived copy accessed November 9, 2026.

How the dollars were restated: each award was multiplied by the September 2026 value of the BLS producer price index for concrete contractors, nonresidential building work (197.561, preliminary) divided by the index in the award month. The El Paso factor is 1.90 and the 2026 Fresno factor is 1.02. The index tracks concrete trade prices, not diamonds or labor productivity, so the 2010 figure is the least reliable row.

What moves the cost of polished concrete floors?

Four things moved the price in the public records: whether flooring or a coating had to come off first, how many square feet were polished, how far the grit sequence went, and how much repair the slab needed. Densifier and guard were in every scope, so they did not separate the cheap jobs from the expensive ones. Aggregate exposure was never priced as its own line.

Removing carpet, VCT or an old coating

All five 2021 to 2026 awards started with demolition. JBER removed carpet, cove base and adhesive from 3,100 sq ft and asked for asbestos test results before work; Fresno 2026 found vinyl asbestos tile in one 8 ft 6 in by 5 ft restroom, according to the W50S6T26QA021 questions and answers. Abatement by a licensed firm is a separate cost that these awards did not price per sq ft.

Coatings cost more to remove than carpet. The GSA St. Louis statement of work required stripping all coatings dry with carbide discs before the first 40 grit pass, and Fresno 2024 began by grinding off an epoxy floor. Those two jobs, at $16.06 and $13.80 per sq ft, are the most expensive per foot in the set.

Job size

Grinders, dust collection and crews cost the same to mobilize for 1,000 sq ft as for 5,000 sq ft. In the records, jobs of 2,405 sq ft or less paid $13.80 to $16.06 per sq ft for coating removal, while the 3,100 and 4,900 sq ft carpet-removal jobs paid $6.92 and $7.40. The two bare-slab jobs over 2,500 sq ft paid $3.92 and $4.11 as awarded.

Grind level and gloss

Each extra diamond step is one more pass over every square foot. JBER stopped at 400 grit, Fresno 2026 and CRREL stopped at 800, and GSA St. Louis ran ten steps to 2000 grit with a dye. The 2000 grit job was the most expensive per foot, but it was also small, after hours and coated, so the public data cannot isolate the price of gloss alone.

Densifier and guard

A densifier is a silicate liquid that reacts with the cement paste to harden the surface; a guard is a thin penetrating or topical treatment applied after the last grit. Every scope here used both: potassium densifier at CRREL in 2018, two densifier coats at GSA in 2022, two guard coats at JBER in 2025, and lithium silicate densifier with a penetrating polyurethane guard at Fresno in 2026.

New slab versus existing slab

A new slab skips demolition but needs planning before the concrete truck arrives. The El Paso courthouse polished 27,000 sq ft of new exposed slab for $4.11 per sq ft in 2010. The CPC aggregate exposure chart says exposure depends on the mix design, placing and finishing, and CPC Position Statement 1 assigns slab protection after placement and after polishing to the general contractor, not the polisher.

For the slab itself, our guide to concrete slab cost per square foot puts commercial slab-on-grade at $10 to $16 installed as of 2026. Polishing is added on top of that number, and the slab needs to cure first; the slab used in the 2015 TCNA slip test was cured 33 days before grinding.

How do specs define grit, gloss and aggregate exposure?

The Concrete Polishing Council (CPC) of the American Society of Concrete Contractors publishes the two charts specifiers cite. The appearance chart sets four gloss levels by distinctness of image (DOI) measured to ASTM D5767, with haze under 12 for every level. The exposure chart sets three classes by the share of surface showing cement, sand or stone.

CPC levelNameAverage DOIAverage 60 degree gloss (optional)Grit the public SOWs asked forSource
1Flat (ground)0 to 9Under 10Not used in these recordsCPC chart, 2-2024
2Satin (honed)10 to 395 to 25400 grit (JBER 2025); Fresno 2026 Q&A: “400 to 800 grit [satin/honed]”CPC chart; SAM.gov
3Polished40 to 69Over 35800 grit (CRREL 2018, Fresno 2024)CPC chart; SAM.gov
4Highly polishedOver 70Over 501500 and 2000 grit resin (GSA 2022); may require groutingCPC chart; SAM.gov

The CPC chart does not tie a level to a grit number, because the same diamond can produce different clarity on different slabs. It requires at least 3 readings on areas up to 1,000 sq ft plus 1 reading per additional 1,000 sq ft, taken within 72 hours of finishing and before any guard goes on. Write those numbers into the bid documents if gloss matters.

CPC classCommon nameSurface makeup (random 10 ft x 10 ft square)What decides itSource
ACream finish85 to 95% cement fines, 5 to 15% fine aggregateShallow grind; flat, well-finished slabCPC exposure chart, 2-2024
BSalt and pepper85 to 95% fine aggregate (sand), 5 to 15% blendGrind through the paste into sandCPC exposure chart
CCoarse aggregate (full exposure)80 to 90% full aggregate, 10 to 20% blendDeeper grind; mix, placing and FF/FL flatnessCPC exposure chart

No public award priced exposure classes as separate lines, so there is no sourced dollar difference between cream, salt and pepper and full aggregate. On an existing slab the class is limited by how the slab was placed years ago; the CPC calls for a mock-up on the actual slab, which is what Fresno required in 2026 with 200 sq ft per building.

Is polished concrete slippery when wet?

In lab tests, no: every polished section in the 2015 TCNA study measured above the 0.42 wet dynamic coefficient of friction (DCOF) that ANSI A326.3-2021 sets for level interior floors walked on when wet. Gloss lowered the number, from 0.56 to 0.58 at low gloss to 0.49 to 0.51 at very high gloss, while aggregate exposure barely moved it.

ANSI A326.3 replaced the method in ANSI A137.1 section 9.6 in 2017, according to the Tile Council of North America, and both use the BOT 3000E device with a wet sodium lauryl sulfate solution. The standard’s informative notes suggest at least 0.50 for Interior, Wet Plus areas such as quick-service dining rooms and 0.55 for oil and grease areas. The very high gloss lab averages of 0.49 to 0.51 sit below those two values.

Gloss level (2015 test)Large aggregateMedium aggregateSalt and pepperCreamSource
Low0.560.580.580.58TCNA-661-14
Medium0.530.500.560.55TCNA-661-14
High0.510.510.530.52TCNA-661-14
Very high0.490.500.490.51TCNA-661-14
Wet DCOF of polished concrete by gloss level and aggregate exposureGrouped bars: wet DCOF falls from 0.56 to 0.58 at low gloss to 0.49 to 0.51 at very high gloss00.20.40.60.8Wet DCOF0.560.580.580.58Low gloss0.530.50.560.55Medium gloss0.510.510.530.52High gloss0.490.50.490.51Very high glossLarge aggregateMedium aggregateSalt and pepperCream
All 16 averages stay above 0.42; gloss moved DCOF more than aggregate exposure did. Source: TCNA-661-14 (January 2015), accessed November 9, 2026.

The lab slab was clean, new and untreated by a guard. Field floors pick up dust, cleaner residue and wear, so the Fresno 2026 solicitation specified a micro-aggregate traction additive in the final guard coat. The CPC position statement on slip resistance reports the 2015 program as 576 tests on 48 sections.

What would a 10,000 sq ft retail floor cost?

About $75,200 for a 10,000 sq ft retail sales floor with vinyl or carpet removed and a 400 to 800 grit finish, using the 2026 Fresno award rate of $7.52 per sq ft in September 2026 dollars. The same floor priced at the highest records in the set, coating removal on small rooms to 2000 grit, would reach $181,000.

LineBasisRate per sq ft10,000 sq ft
Low case: carpet out, 400 grit, stain, 2 guard coats, cove baseJBER 2025 award $6.92, PPI factor 1.0573$7.31$73,100
Base case: vinyl and carpet out, 40 to 800 grit, lithium densifier, guard with traction additive, mock-up, ASTM F2170 testFresno 2026 award $7.40, PPI factor 1.0160$7.52$75,200
New slab, nothing to remove, hone and polish with densifierEl Paso 2010 award $4.11, PPI factor 1.8996$7.81$78,100
Carpet and laminate out plus sound panels (3-bid low)Madera 2021 low bid $12.48, PPI factor 1.3796$17.22$172,200
High case: coatings stripped, 2000 grit with dye, after hoursGSA 2022 award $16.06, PPI factor 1.1274$18.10$181,000

Three things are not in the base case. Fresno asked bidders to list crack, joint and spall repair as a separate line because nobody could see the slab under the flooring, so carry those as unit prices. Asbestos abatement is a licensed trade with its own contract. Moisture testing to ASTM F2170 is included in the Fresno scope but not in the JBER scope.

Size works in the buyer’s favor here: 10,000 sq ft is twice the area of the largest recent existing-slab award, so the base rate is a ceiling for a sound slab with soft flooring, not a floor. For the full fit-out budget around it, see our guide to retail construction costs, and check what the lease’s tenant improvement allowance covers before choosing a finish.

Is polished concrete cheaper than epoxy?

On a large, sound slab the two are close at install: $7.40 per sq ft for the 2026 Fresno polish versus $7.00 for a 30 mil epoxy roll coat in the City of Tulsa’s 2024 bid. In the same St. Louis federal building, GSA paid $16.06 per sq ft to polish a hallway in 2022 and $17.78 per sq ft for epoxy on a 2,147 sq ft hallway in 2023.

ComparisonPolished concreteEpoxySource
Large area, public bid$7.40 per sq ft, 4,900 sq ft, Fresno 2026$7.00 per sq ft, 30 mil roll coat over 2,000 sq ft, Tulsa 2024USAspending.gov; City of Tulsa IFB 25-809
Same building, small hallway$16.06 per sq ft, 2,405 sq ft, July 2022$17.78 per sq ft, 2,147 sq ft, May 2023USAspending.gov, GSA St. Louis
Thickness added to slabNone; the slab surface is the floor30 mils (0.030 in) and upFresno SOW; Tulsa IFB
Damp slabNo film to blister; Fresno still required an ASTM F2170 testMoisture limits apply to standard resinsSAM.gov W50S6T26QA021; our epoxy guide
Hot water, chemicals, forkliftsExposed concrete; guard is thinThicker mortar or urethane cement systems availableTulsa IFB 25-809

The price of an epoxy floor climbs with thickness and chemical resistance, which polished concrete does not offer. Our epoxy flooring cost guide lists the Tulsa systems from $7.00 to $17.50 per sq ft. Kitchens have their own rules on coving and slip, covered in our commercial kitchen flooring guide.

What does polished concrete maintenance cost?

No public owner record we could open priced routine polished concrete maintenance per square foot as of November 2026, so this page gives no dollar figure for it. What the public scopes do show is what gets bought at install, which sets the maintenance cycle: two guard coats at JBER in 2025 and a penetrating polyurethane guard at Fresno in 2026.

Item to price as a bid alternateWhy it mattersUnit to request
Re-apply guard (same product as installed)JBER required 2 coats and Fresno a traction additive in the guard; both wear in traffic lanes$ per sq ft per application
Burnish visitCRREL’s 2018 scope ended with a burnish to 800 to 1500 sheen$ per sq ft per visit
Re-hone last grit steps (for example 400 and 800)Restores clarity without regrinding to 40 grit$ per sq ft
Gloss and DOI readings after the workCPC chart: 3 readings up to 1,000 sq ft plus 1 per 1,000 sq ft$ per visit

Asking for these four unit prices in the original bid locks rates while bidders compete, which is when the public records show prices at their lowest: 16 and 18 offers produced the $6.92 and $7.40 awards. Our guide on how to compare construction bids covers lining up unit prices across bidders.

How should you scope the bid so the low bidder delivers?

Write the result you want in measurable terms and make bidders prove it on your slab. The 2024 Fresno job, awarded at $13,800, was terminated for default for not performing to the statement of work. The 2026 rebid at the same base added a moisture test, a 200 sq ft mock-up in each building, a named densifier and guard, and a separate repair line, and drew 18 offers.

IfThenThreshold or source
Carpet, VCT, laminate or adhesive covers the slabPrice removal in the polish bid; test old tile and mastic for asbestos firstJBER 2025 sampled for asbestos; Fresno 2026 found asbestos tile
An epoxy or other coating is on the slabExpect the upper end of the range$13.80 to $16.06 per sq ft (Fresno 2024, GSA 2022)
Polished area is under 2,500 sq ftBundle rooms into one mobilization or expect about twice the per-foot price1,000 and 2,405 sq ft jobs vs 3,100 to 4,900 sq ft jobs
Floor may be walked on wetSpecify wet DCOF of 0.42 or more and a traction additive in the guardANSI A326.3-2021; Fresno 2026 Q&A
Quick-service dining or grease exposureCheck the 0.50 and 0.55 informative values before choosing very high glossANSI A326.3 notes; TCNA very high gloss 0.49 to 0.51
Gloss matters to the ownerSpecify CPC level and DOI range, readings within 72 hoursLevel 3 DOI 40 to 69; Level 4 over 70
Slab condition under flooring is unknownMake crack, joint and spall repair a separate unit-price lineFresno 2026 Q&A answer 8
New buildingSpecify the slab for polishing and assign protection to the general contractorCPC Position Statement 1
Flowchart of four pricing questions: existing flooring, area under 2,500 sq ft, wet use, Level 4 gloss Pricing a polished concrete floor: four questions in order Carpet, VCT, laminate, epoxy or adhesive on the slab now? Yes Price removal and grinding off 2021 to 2026 awards: $6.92 to $16.06 No Polished area under 2,500 sq ft? Yes Expect the upper end: $13.80 (1,000 sq ft) and $16.06 (2,405 sq ft) awards No Floor gets wet: entries, break rooms, wash-down areas? Yes Guard with traction additive; specify wet DCOF of 0.42 or more (ANSI A326.3) No Mirror-like Level 4 look (DOI above 70) wanted? Yes Plan 1500 to 2000 grit plus grouting; GSA 2000 grit job: $16.06 per sq ft No Bare, sound slab with nothing to remove: grind, densify and polish. Federal awards paid $3.92 (2018) and $4.11 (2010), or $6.14 and $7.81 in September 2026 dollars Sources: USAspending.gov and SAM.gov awards 2010 to 2026; ASCC Concrete Polishing Council chart (2024); ANSI A326.3.
Four questions set the price band before bidding; amounts are 2010 to 2026 public awards as awarded. Sources: USAspending.gov, SAM.gov, CPC chart (2024), ANSI A326.3-2021, accessed November 9, 2026.

The 2026 Fresno solicitation is a usable template for an existing slab. Its sequence, from the statement of work and the bidder questions and answers, runs in this order:

  1. Remove flooring and adhesive (carpet, vinyl, glue, mastic) with a concrete grinder.
  2. Run the mandatory moisture test to ASTM F2170 (in-situ relative humidity).
  3. Repair and fill cracks and joints; Fresno named a semi-rigid polyurea joint filler.
  4. Grind at 40, 80 and 150 grit.
  5. Apply lithium silicate densifier (about 3,500 sq ft in Building 102 and 1,400 sq ft in Building 110).
  6. Hone and polish at 400 and 800 grit.
  7. Apply the guard: a penetrating polyurethane with a micro-aggregate traction additive.
  8. Measure DOI, gloss and haze within 72 hours, per the CPC appearance chart.
Eight steps from flooring removal through 40 to 800 grit, densifier and guard to DOI readings The 2026 Fresno ANG sequence for an existing slab (HAYW262010) 200 sq ft mock-up in each building, accepted before production work 1 Remove flooring and adhesive carpet, vinyl, glue, mastic 2 Moisture test ASTM F2170 (in-situ RH) 3 Repair cracks and joints semi-rigid polyurea joint filler 4 Grind 40, 80, 150 grit 5 Densify lithium silicate densifier 6 Hone and polish 400, 800 grit 7 Guard penetrating polyurethane + traction additive 8 Measure DOI, gloss, haze within 72 hours (CPC chart) Sources: SOW HAYW262010 and Q&A (SAM.gov W50S6T26QA021, 2026); ASCC CPC appearance chart (2024).
The 2026 Fresno Air National Guard scope ran 40, 80, 150, 400 and 800 grit with a lithium densifier and a traction guard. Source: SOW HAYW262010 and Q&A, SAM.gov W50S6T26QA021, accessed November 9, 2026.

For the rest of the package, our guide to estimating construction costs shows how to carry unit-price lines, and the warehouse version of this decision, with flatness numbers, is in our warehouse construction guide.

A good polished floor starts with the mix delivered on the day, so see our concrete slump test guide, and compare walls and finishes in our cinder block wall cost guide.

How we compiled this

We searched USAspending.gov and SAM.gov for polished concrete awards, read the 6 federal solicitations and statements of work behind them, and recovered the City of Madera bid results and council report through the Internet Archive after the city’s links stopped working. We kept only records that state both a dollar amount and an area, restated them with BLS index PCU23811X23811X, and read the CPC charts, the TCNA report and ANSI A326.3 in November 2026. We excluded contractor and consumer cost guides, and bid tabs we could not open at the source.

Frequently asked questions

Is polished concrete cheaper than tile or carpet?

Often at install when the slab is sound and large. Two federal awards that removed carpet and polished 3,100 and 4,900 sq ft cost $6.92 and $7.40 per sq ft in 2025 and 2026. Small rooms with an old coating to grind off cost $13.80 to $16.06 per sq ft. Get tile and carpet bids on the same area and date to compare like for like.

How long does it take to polish a commercial concrete floor?

The public scopes allowed 30 working days for 4,900 sq ft at Fresno in 2026, 45 days for 5,600 sq ft at the Madera police building in 2021, and 60 calendar days for 2,405 sq ft of after-hours work at GSA St. Louis in 2022. Those periods include removing old flooring, repairs and cure time for the guard.

What grit level should a commercial polished concrete floor be?

The recent federal scopes stopped at 400 grit (JBER 2025) or 800 grit (Fresno 2026, CRREL 2018), which Fresno described as satin or honed. GSA went to 2000 grit for a high-gloss hallway. Specify the CPC appearance level and its DOI range rather than a grit number, because the chart measures the result, not the diamond.

Do you need a densifier and a guard on polished concrete?

Every public scope we read used both. CRREL specified a potassium densifier in 2018, GSA two densifier coats in 2022, JBER at least two guard coats in 2025, and Fresno a lithium silicate densifier with a penetrating polyurethane guard and traction additive in 2026. Ask bidders to name the products and coverage rates in the bid.

Can any existing concrete slab be polished?

Most can, but the slab sets the limits. The CPC exposure chart says the visible aggregate depends on the original mix, placing and finishing, so an old slab may not reach Class C full exposure evenly. Fresno required a 200 sq ft mock-up per building and an ASTM F2170 moisture test before production in 2026.

Does polished concrete meet slip resistance requirements?

In the 2015 TCNA lab study, all 48 polished sections measured above 0.42 wet DCOF, the ANSI A326.3 value for level interior floors walked on when wet. Very high gloss averaged 0.49 to 0.51, below the standard’s 0.50 and 0.55 informative values for quick-service and grease areas, so test the finished floor where those apply.

Sources

Last reviewed November 2026 by the CB&C Editorial Team. See our editorial standards.

← Back to all articles